Choose your country / language

Beyond Surfaces #1 - Intelligent Coating Solutions

ค้นหาข้อมูลเพิ่มเติมเกี่ยวกับเรื่องราวของกลุ่มธุรกิจได้ในวารสารสำหรับลูกค้าฉบับแรกของเรา!

Beyond Surfaces #1 - Intelligent Coating Solutions

ขณะนี้แบรนด์ Oerlikon Balzers และ Oerlikon Metco ได้ทำงานร่วมกันเป็นเวลาเกือบสองปีแล้วภายใต้กลุ่ม Surface Solutions ของกลุ่มบริษัท Oerlikon Group

ไขปัญหาการเคลือบที่ชาญฉลาดสำหรับอุตสาหกรรมการบินและอวกาศรวมทั้งอุตสาหกรรมยานยนต์ หรือสำหรับอาคารที่มีชื่อเสียงที่สุดแห่งหนึ่งของโลก และแม้กระทั่งห้วงอวกาศ – ตื่นตาตื่นใจกับเรื่องราวอันน่าทึ่งเกี่ยวกับวิธีที่เราและลูกค้าของเราสร้างชีวิตให้กับ Surface Solutions!

พลิกอ่านวารสาร

Protective coating for water turbines

Hydropower turbines are subjected to enormous forces and damage mechanisms. Over time, erosion and cavitation lead to major efficiency losses and a marked reduction in useful lifetime. To hinder this, turbine manufacturers rely on hightech coatings from Oerlikon Balzers and Oerlikon Metco.

Protective coating for water turbines

The demand for energy is constantly increasing, driven by population growth and increasing prosperity in emerging countries. One of the most environmentally-friendly types of energy generation is the use of hydropower – using run-of-river hydropower plants placed directly in the river course which constantly generate power, or pump-storage power plants (e.g. reservoirs), which are used to store energy for release upon demand – a function of ever increasing importance.

Decisive factor: Economic efficiency

Power plant operators are focused on ever higher turbine economic efficiency, through extended useful lifetime, longer inspection cycles and higher efficiency. At the same time, a growing number of new waterways, previously deemed too inaccessible, are now being tapped – often highly sandy rivers or waters with high head. Wear protection for individual power plant components is thus a key factor for the success of these projects.

Specialists for all cases

Oerlikon Metco provided the first coatings for Francis turbines in the 1930’s, and, since the 1980’s, has protected thousands of turbine runners in hydropower plants throughout the world with its thermal spray coatings, which can be up to 400 μm (0.4 mm) thick. The coatings are individually tailored – they are dependent on machine design, precise operating mode and specific operation conditions.
Oerlikon Balzers is, then again, a specialist for extremely thin PVD coatings. Not just cutting tools used to manufacture turbine parts are coated with BALINIT, but also bearings or valves in the overall system. The goal of both applications is to reduce wear caused by friction and thereby to increase efficiency.

Find more about our Products & Services

FACTS & FIGURES - Individually tailored

The right coating not only enables extended service life, but also longer inspection cycles and higher efficiency. Both turbine design (Pelton, Francis, Kaplan) and operating conditions are crucial factors for the customization process. Pelton turbines are, for example, used in areas with high head (more than 100 metres) and small water quantities. In the opposite case – namely with lower head and large water quantities – a Kaplan turbine is generally used. The design of the latter makes it more susceptible to destructive cavitation, which affects both the choice of coating and the turbine parts to be coated. The choice of wear protection must also consider not just the amount of silt, sand and shingle that is carried along with the water, but also chemical contamination.

ติดต่อเรา

Petra Ammann

Petra Ammann

Head of Communications Oerlikon Balzers
keyboard_arrow_up